GRAT IoT Mini Actuator RS485 Modbus Smart Signal Remote Control for Building Automation
GRAT WA-20 / WA-50 IoT Mini Electric Actuator: built-in controller, encoder and OLED in one housing, no external driver. 20 or 50 Nm, 0.5 % accuracy, 4-20 mA / 0-10 V / Modbus RTU, IP65 and -30 C operation for DN25-DN40 ball valves.
RS485 Modbus mini actuator
,smart signal remote control actuator
,IoT actuator for building automation
WA Series — Compact Modulating Electric Actuator. The controller is inside. The cabinet isn't needed.
GRAT's WA-20 and WA-50 integrate the brushless drive, encoder, controller and OLED display in a single compact housing. Two size classes cover small ball valves with analog or Modbus RTU control — there is no external driver to mount, wire or commission.
Both variants adopt a common housing platform, identical control hardware and signal interface options. The only distinctions lie in their torque rating and mechanical mounting interface. Full details of all differentiating parameters can be found within the comparison table in Section 02.
The compact modulating actuator.
The higher-torque modulating actuator.
| Parameter | WA-20 | WA-50 |
|---|---|---|
| Rated torque | 20 N·m | 50 N·m |
| Ball valve size | DN25 and smaller | DN32–DN40 |
| Control mode | Modulating (encoder regulation) only | Modulating (encoder regulation) or On/Off |
| Output drive | Recessed octagonal □ 11 × 11 mm | Recessed octagonal □ 14 × 14 mm |
| Mounting holes | 4-M5 (Ø50) · 4-M6 (Ø36) | 4-M8 (Ø70) · 4-M6 (Ø50) |
| Housing envelope (W × D × H) | 88.5 × 68.5 × 85.4 mm | 108 × 93 × 92 mm |
- One housing, no driver Brushless motor, encoder, controller and OLED display share one enclosure. Nothing extra to mount in the cabinet or to wire on site.
- Positioning you can trust Encoder regulation with position feedback; a stepless speed setting lets the stroke slow down when a valve seat needs gentle closing.
- Bus-ready by default Position, fault codes and supply status go to a PLC, SCADA or IoT gateway over the existing cable, and can be read on the onboard display without opening the housing.
- Serviceable in the field Hex-key manual override and power-off position hold keep the valve under control during commissioning and maintenance.
| Parameter | Specification |
|---|---|
| Supply | DC 24 V / AC 220 V |
| Control signal in | 4–20 mA · 0–10 V · 1–5 V |
| Position feedback out | 4–20 mA |
| Protocol | RS-485 / Modbus RTU |
| Motor | 10 W brushless, built-in overload protection |
| Control accuracy | 0.5 % with encoder regulation |
| Speed setting | Stepless PWM, 30–100 % adjustable |
| Action time / rotation | 15–25 s for 0–90° |
| Installation orientation | 360° adjustable |
| Protection / low-temperature operation | IP65 · −30 °C |
| Insulation / withstand voltage | 100 MΩ at 500 V DC · 1,500 V AC for 1 min |
| Electrical interface / manual operation | M20 × 1.5 cable gland · hex key |
| Control circuit / optional | Type S / MS / PCU / DRS · OLED display, IoT communication, LOS reset |
| Testing standard | JB/T 8219-2016, GB/T 3836.1-2021 |
Figures are taken from the official GRAT selection manual, dimension drawings and wiring diagrams.
Designed for standard industrial service and suitable for indoor or covered outdoor mounting. If deployed in locations with direct rainfall, frequent wash-down or corrosive surroundings, contact GRAT for a higher-protection version or an outdoor housing. When operating beyond these limits, our standard quarter-turn electric actuator series is the proper selection.
CDU liquid cooling and cooling loops — compact modulating control in a space-tight cabinet.
BMS and chilled water — modulating control straight from the BMS, no separate positioner.
Filtration and backwash valves — proportional throttling instead of on/off only.
Automatic igniters and compact process valves — one housing for drive, control and indication.
Many engineers benchmark the WA series against actuators requiring an external drive unit, or solenoid valves. Modulating applications demand stepless positioning across the full 0–100 % stroke range, while solenoid valves simply operate in an on/off fashion.
| Feature | GRAT WA Series | Other Mini Actuator | Solenoid Valve | Basic Electric Actuator |
|---|---|---|---|---|
| Built-in controller | Yes | No | No | No |
| OLED display | Yes | No | No | No |
| IoT communication | Yes | No | No | No |
| Compact design | Yes | No | Yes | No |
| High precision | Yes | No | No | Yes |
| LOS reset | Yes | Yes | No | No |
| Low-temperature operation | Yes | No | No | No |
| Energy saving | Yes | No | No | No |
GRAT is a Wuhan-based manufacturer of valves and actuators, equipped with in-house CNC machining facilities and assembly lines; we are not a reseller. Pre-delivery testing includes torque, insulation, hi-pot, functional and ageing tests, and a dedicated test record is kept for every serial number.
- Product Catalogue Full WA series specification, model codes and wiring.
- WA-20 Instruction Manual Installation, wiring, Modbus addresses and fault codes.
- WA-50 Instruction Manual The same document set for the higher-torque model.
- Dimension Drawings Three outline drawings, reproduced in Section 04.
- Wiring Diagrams DC 24 V and AC 220 V variants, also in Section 04.
Supplier onboarding packs, certificates, test reports and factory visits are handled by the same team — just ask.
Send valve size, medium, pressure differential and control signal. We reply within one working day with a model code and a torque opinion, not a brochure. Datasheet, drawings and wiring diagrams are supplied with the order.
Scan to add on WeChat